Step Title Time Command Command Cmd Seq Telemetry Telemetry Expected Units Telemetry Other Crit Description Notes RT Tlm Min SIM \# Req (m) Description Mnemonic EGSE Key Description Mnemonic Value EGSE Verifier Con Fmt Alt Pos 2.13\_V2.0 1.0 Verify Initial Temperatures 1.1 Verify HW Temperatures Camera Body T A 1CBAT $+25\pm2$ C 2 should be at $+25\pm2$~C Y 1or2 Camera Body T B 1CBBT $+25\pm2$ C 2 should be at $+25\pm2$~C Cold Radiator T A 1CRAT $\sim-44$ C Cold Radiator T B 1CRBT $\sim-44$ C Warm Radiator T A 1WRAT $\sim-32$ C 2 Warm Radiator T B 1WRBT $\sim-32$ C 2 1.2 verify FP temperature 2 FP Temp $\sim +30$ C deaHousekeepingData A verify FP temp stable at desired temp. Y 1or2 2.0 Start Cooling DH to -60 C 2.1 Housing Bakeout Off B 1 Housing B.O. Off B 1HBOBOF DA BO B On/Off 1DABOBON OFF Y 1or2 DA Htr Output V B 1DAHBVO 0.0 V 1 voltage should drop to 0 DA Htr Current B 1DAHBCU 0.0 A 1 current should drop to zero 2.2 Housing Bakeout Dis B 1 Housing B.O. Dis B 1HBOBDS DA BO B Enb/Dis 1DABOBEN DIS Y 1or2 2.3 monitor Camera Body temp 60 Camera Body T A 1CBAT $<+25$ C 2 wait for a significant P 1or2 Camera Body T B 1CBBT $<+25$ C 2 drop below $+25\pm2$~C 3.0 Drop FP temp gradually 3.1 drop FP temp to +20~C 30 ChangeConfigSetting WSFTPOS\_20 FP Temp $+20$ C Check cmdResult = 1 A after Camera Body temp is $<+20$~C Y 1or2 commandEcho 225 deaHousekeepingData 3.2 drop FP temp to +10~C 30 ChangeConfigSetting WSFTPOS\_10 FP Temp $+10$ C Check cmdResult = 1 A after Camera Body temp is $<+10$~C Y 1or2 commandEcho 226 deaHousekeepingData 3.3 drop FP temp to +0~C 60 ChangeConfigSetting WSFTPOS\_00 FP Temp 0 C Check cmdResult = 1 A after Camera Body temp is $<0$~C Y 1or2 commandEcho 228 deaHousekeepingData 3.4 drop FP temp to -10~C 60 ChangeConfigSetting WSFTNEG\_10 FP Temp $-10$ C Check cmdResult = 1 A after Camera Body temp is $<-10$~C Y 1or2 commandEcho 231 deaHousekeepingData 3.5 drop FP temp to -20~C 60 ChangeConfigSetting WSFTNEG\_20 FP Temp $-20$ C Check cmdResult = 1 A after Camera Body temp is $<-20$~C Y 1or2 commandEcho 232 deaHousekeepingData 3.6 drop FP temp to -30~C 60 ChangeConfigSetting WSFTNEG\_30 FP Temp $-30$ C Check cmdResult = 1 A after Camera Body temp is $<-30$~C Y 1or2 commandEcho 235 deaHousekeepingData 3.7 drop FP temp to -40~C 60 ChangeConfigSetting WSFTNEG\_40 FP Temp $-40$ C Check cmdResult = 1 A after Camera Body temp is $<-40$~C Y 1or2 commandEcho 237 deaHousekeepingData 4.0 Disable FP bakeout 4.1 Verify Camera Body Temp 60 Camera Body T A 1CBAT $-60$ C 2 should be at $-60$~C Y 1or2 Camera Body T B 1CBBT $-60$ C 2 4.2 set FP temp to -120~C 2 ChangeConfigSetting WSFTNEG120 Check cmdResult == 1 A Y 1or2 commandEcho 105 4.3 turn off FP bakeout htr 2 ChangeConfigSetting WSBAKDSABL Check cmdResult == 1 A Y 1or2 commandEcho 116 Y 1or2 4.4 disable bakeout patch 2 writeBep WBBOEN\_DIS Check cmdResult == 1 A Y 1or2 commandEcho 99 4.5 set warm boot flag on 0.1 DPA Warm Boot 1WRMBTSB(1) 2 Y 1or2 4.6 Halt BEP 0.1 DPA Command Reset 1RSETIRT(1) 2 1RSETIRT=1 holds board in reset Y 1or2 4.7 Restart BEP 0.1 DPA Command Reset 1RSETIRT(0) 2 1RSETIRT=0 releases board Y 1or2 4.8 Check BEP A Boot 2.0 Check bepStartupMessage: A Y 1or2 bepTickCounter $< 10$; warmbootFlag =1; A watchdogFlag = 0, patchValidFlag =1 A Check swHousekeeping messages: startingBepTickCounter $< 10$; B endingBepTickCounter= B =startingBepTickCounter+640 4.9 Check HW LEDs 2.0 BEP Select 1STAT4ST 0 2 0 indicates BEP A is selected Y 1or2 BEP FIFO Not Full 1STAT6ST 1 2 1 means FIFO not full BEP FIFO Not Empty 1STAT7ST 0 2 1 means FIFO not empty 4.10 Check SW LEDs 2.0 BEP initialization 1STAT3ST 0 2 0 means BEP SW is running Y 1or2 Watchdog boot 1STAT2ST 1 2 1 means no watchdog boot Science run status 1STAT1ST 1 2 1 means science idle 1STAT0ST 0or1 2 this bit toggles to indicate BEP is running 5.0 Monitor FP Temp 5.1 Load Board 11 DEA HK 1 loadDeaBlock WD00001024 Check cmdResult == OK B Load Fullhouse DEA housekeeping Y 1or2 commandEcho 225 parameter block into slot 4 5.2 Start DEA Hkp run 1 startDEA XDZ0000005 Check cmdResult == OK B get FP temp from DEA HKP data Y 1or2 commandEcho 18 5.3 dump system config. 0.1 dumpSysConfig RS\_0000001 Check cmdResult == OK B Y 1or2 commandEcho 66 5.4 Monitor FP temp 480 FP Temp $<-60$ C deaHousekeepingData A after $\sim1/2$~hr, should be convinced temp is P 1or2 dropping, objective is stabilization at -120~C P 1or2 Total Time 978.4