Step Title Time Command Command Cmd Seq Telemetry Telemetry Expected Units Telemetry Other Crit Description Notes RT Tlm Min SIM \# 4.29\_V2.2 (mins) Description Mnemonic EGSE Key Description Mnemonic Value EGSE Verifier Con Fmt Alt Pos 1 Turn on DEA A 1.1 Verify DEA B is off DEA B ENB/DIS 1DEPSBX DIS 1,2,4,6 DEA B ON/OFF 1DEPSB OFF DEA Input V B 1DE28BVO 25.0--34.0 V DEA +28 V B 1DEP3BVO $0.0\pm0.5$ V DEA +24 V B 1DEP2BVO $0.0\pm0.5$ V DEA +15 V B 1DEP1BVO $0.0\pm0.5$ V DEA +6 V B 1DEP0BVO $0.0\pm0.5$ V DEA -6 V B 1DEN0BVO $0.0\pm0.5$ V DEA -15 V B 1DEN1BVO $0.0\pm0.5$ V 1.2 Verify DEA A is DEA Input V A 1DE28AVO 25.0-–34.0 V 1 receiving power 1.3 Enable DEA PS A 1 DEA PS A En 1DEPSAEN DEA A ENB/DIS 1DEPSAX ENB 2 1,2,4,6 1.4 DEA Power A On 1 DEA PS On A 1DEPSAON DEA A ON/OFF 1DEPSA ON 2 1,2,4,6 DEA Input V A 1DE28AVO 25.0--34.0 V 2 Expect DEA side A power DEA +28 V A 1DEP3AVO $>26.0$ V 2 $24\pm4$~W, current is noisy DEA +24 V A 1DEP2AVO 24.0--26.0 V 1 so average needed (see figures). DEA +15 V A 1DEP1AVO 15.0--17.0 V 2 DEA +6 V A 1DEP0AVO 5.6--6.7 V 2 {\bf FP Temp unregulated} DEA -6 V A 1DEN0AVO -7.0{--}-5.7 V 2 {\bf DEA Interface A/D} DEA -15 V A 1DEN1AVO -17.0{--}-15.0 V 2 {\bf in low-res mode} DEA Input I A 1DEICACU 0.7--0.9 A 2 1.5 Verify DEA B is off DEA B ENB/DIS 1DEPSBX DIS 1,2,4,6 DEA B ON/OFF 1DEPSB OFF DEA Input V B 1DE28BVO 25.0--34.0 V DEA +28 V B 1DEP3BVO $0.0\pm0.5$ V DEA +24 V B 1DEP2BVO $0.0\pm0.5$ V DEA +15 V B 1DEP1BVO $0.0\pm0.5$ V DEA +6 V B 1DEP0BVO $0.0\pm0.5$ V DEA -6 V B 1DEN0BVO $0.0\pm0.5$ V DEA -15 V B 1DEN1BVO $0.0\pm0.5$ V 2 Heater States 2.1 Verify heaters are not DA HTR EN/DIS A 1DAHTAEN DIS 2 powered on side A DA HTR ON/OFF A 1DAHTAON OFF 2 DA BAKE OUT EN/DIS A 1DABOAEN DIS 2 DA BAKE OUT ON/OFF A 1DABOAON OFF 2 3 Warm boot BEP 3.1 Set Boot modifier off DPA FS Boot Modifier 1BMODIBM(0) disables boot from uplink LF 4.4.1 1,2,4,6 3.2 Set warm boot flag DPA Warm Boot 1WRMBTSB(1) Warm boot active BEP LF 4.4.1 1,2,4,6 3.3 Halt active BEP Halt BEP 1RSETIRT(1) Hold active BEP reset line LF 4.4.1 1,2,4,6 3.4 Restart active BEP Restart BEP 1RSETIRT(0) Release BEP reset line 1,2,4,6 3.5 Check BEP Boot 2 Check bepStartupMessage: A 1,2,4,6 bepTickCounter $< 10$; version =??; A version \# depends on warmbootFlag = 1, patchValidFlag =1 A loaded patches (if any) Check swHousekeeping messages: startingBepTickCounter $< 10$; B endingBepTickCounter= B {\bf DEA Interface A/D} $=$startingbeptickcounter+640 {\bf in high-res mode} version =?? A 3.6 Check HW LEDs 1 BEP Select 1STAT4ST 0or1 2 0/1 indicates BEP A/B selected 1,2,4,6 BEP FIFO Not Full 1STAT6ST 1 2 1 means FIFO not full BEP FIFO Not Empty 1STAT7ST 0 2 1 means FIFO not empty 3.7 Check SW LEDs 1 BEP initialization 1STAT3ST 0 2 0 means BEP SW is running 1,2,4,6 Watchdog boot 1STAT2ST 1 2 1 means no watchdog boot Science run status 1STAT1ST 1 2 1 means science idle 1STAT0ST 0or1 2 bit toggles $\Rightarrow$ BEP is running 4 Execute DEA {\bf Housekeeping run} 4.1 Load Board 11 DEA HK 1 loadDeaBlock WD00001024 commandEcho 225 B Load Fullhouse DEA hkp 1,2,4,6 Check cmdResult == OK parameter block into slot 4 4.2 Start DEA HK run 1 startDEA XDZ0000005 commandEcho 18 B 1,2,4,6 Check cmdResult == OK confirm DEAhk values 5 Set FP temp to -121~C 5.1 Set FP temp to -121~C 2 ChangeConfigSetting WSFTNEG121 Check cmdResult == OK 1 get FP temp Y 1,2,4,6 commandEcho 1220 5.2 Dump system config dumpSysConfig RS\_0000001 Check cmdResult == OK B Y 1,2,4,6 commandEcho 66 6 Power up all boards 6.1 Power up all video\\boards 1 changeConfigSetting WSVIDALLUP Verify cmdResult==OK\\commandEcho 768 A Wait for all video boards to power up 1DEPSA ON 2 Fail if DEA-A powers down DEA Input I A 1DEICACU 2.3--2.7 A 2 Current is noisy so average DEA +15 V A 1DEP1AVO 15.0--17.0 V 2 needed (Figure 3). pmon A 10 DEACCD\_POWERON msgs 6.2 Power up all FEPs\\ 2 changeConfigSetting WSFEPALLUP Verify cmdResult==OK\\commandEcho 89 A Messages: Y 1,2 60k pmon A 30 FEP\_WRITEMEM pmon A 6 FEP\_EXECMEM pmon A 6 FEPMAN\_POWERON pmon A 6 FEPMAN\_STARTLOAD pmon A 6 FEPMAN\_ENDLOAD DPA Input I A 1DPICACU 1.1{--}1.6 A Should be valid for BEP A or B DPA Input I B 1DPICBCU 1.1{--}1.6 A Should be valid for BEP A or B 6.3 Dump System Config.\\ 1 dumpSysConfig RS\_0000001 Verify cmdResult==OK\\commandEcho 66 B Y 1,2 60k 7 Science run\\on ACIS-I Skip if video housekeeping not desired 7.1 Load Faint TE pblock\\ 1 loadTeBlock WT00C66014 Verify cmdResult==OK\\commandEcho 14458 A Y 1,2 60k 7.2 Start bias-only run\\ 3 startScience X2Z0000005 Verify cmdResult==OK\\commandEcho 48 scienceReport A Verify terminationCode==2\\in scienceReport Y 1,2 60k 8 Science run\\on ACIS-S Skip if video housekeeping not desired 8.1 Load Faint TE pblock\\ 1 loadTeBlock WT00C68014 Verify cmdResult==OK\\commandEcho 14460 A Y 1,2 60k 8.2 Start bias-only run\\ 3 startScience X2Z0000005 Verify cmdResult==OK\\commandEcho 48 scienceReport A Verify terminationCode==2\\in scienceReport Y 1,2 60k 9 Power down all boards 9.1 Power down all video\\ boards and FEPs 1 changeConfigSetting WSPOW00000 Verify cmdResult==OK\\commandEcho 773 A Y 1,2 60k DEA Input I A 1DEICACU 0.7--0.9 A 2 Noisy current; average needed Messages: pmon A 10 DEACCD\_POWEROFF pmon A 6 FEPMAN\_POWEROFF DPA Input I A 1DPICACU 0.4{--}0.6 A DPA Input I B 1DPICBCU 0.4{--}0.6 A 9.2 Dump System Config.\\ 1 dumpSysConfig RS\_0000001 Verify cmdResult==OK\\commandEcho 66 B Y 1,2 60k